|
MCQs: carrying a uniformly distributed load per metre length is suspended at the A pile of length centre and from other two points 0.15 L from either end ; the maximum hogging moment will be_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The design of a retaining wall assumes that the retained earth________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The advantage of a concrete pile over a timber pile, is_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: For stairs spanning horizontally, the minimum waist provided is________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The horizontal portion of a step in a stairs case, is known as_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A foundation rests on_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: An R.C.C. roof slab is designed as a two way slab if________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: If the average bending stress is 6 kg/cm2 for M 150 grade concrete, the length of embedment of a bar of diameter d according to I.S. 456 specifications, is__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Piles are usually driven by________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: In a combined footing for two columns carrying unequal loads, the maximum hogging bending moment occurs at
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The live load to be considered for an inaccessible roof, is______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: If W is total load per unit area on a panel, D is the diameter of the column head, L is the span in two directions, then the sum of the maximum positive bending moment and average of the negative bending moment for the design of the span of a square flat slab, should not be less than________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: If a bent tendon is required to balance a concentrated load W at the centre of the span L, the central dip h must be at least________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The radius of a bar bend to form a hook, should not be less than_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A circular slab subjected to external loading, deflects to form a_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The reinforced concrete beam which has width 25 cm, lever arm 40 cm, shear force 6t/cm2, safe shear stress 5 kg/cm2 and B.M. 24 mt________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: If a rectangular pre-stressed beam of an effective span of 5 meters and carrying a total load 3840 kg/m, is designed by the load balancing method, the central dip of the parabolic tendon should be_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: If the effective length of a 32 cm diameter R.C.C. column is 4.40 m, its slenderness ratio, is_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The anchorage value of a hook is assumed sixteen times the diameter of the bar if the angle of the bend, is___________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The number of treads in a flight is equal to_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
