Process Equipment & Plant Design Mcqs for Chemical


Q.  Cylindrical pressure vessels in horizontal condition is generally supported on a ________________ support?

a. Lug
b. Skirt
c. Saddle
d. Guy wire


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  With increase in temperature drop (in a shell and tube heat exchanger), the LMTD correction factor, FT_________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  The distance between the top of the slots and the liquid surface when the static liquid is just ready to flow over the overflow weir is called____________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Minimum recommended baffle spacing in a shell and tube heat exchanger is about (where, D = shell diameter) ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  In a cylindrical vessel subjected to internal pressure, the longitudinal stress ζL and the circumferential stress, ζn are related by___________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Larger depth of liquid on the trays of a distillation column_________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Needle valves are generally not used for___________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  In common bubble cap distillation column design practice, riser area is approximately equal to (where, Aa = Annular passage area, and Sa = Slot area) ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Welded joint efficiency in the design of chemical process equipment is taken as_________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Floating head heat exchangers are used for the____________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Theoretically calculated diameter of the stripping section of the continuous rectification column is ______________ that of the enriching section?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Safety valves are provided in chemical equipments to guard against excessive_________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  An adequate clearance between the tray and the shell wall of a distillation column is provided to_____________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  A forced circulation long tube vertical evaporator as compared to the natural circulation evaporator__________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Cylindrical storage tanks used for the storage of volatile liquids (e.g., naphtha) have ______________ roofs?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  What is the slope of the operating line in the stripping section of a distillation column ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  The safe height (h) to diameter D. ratio (i.e., h/d) for liquid/petro fuel storage tank of capacity more than 45 kilolitres is less than _________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Ponchon Savarit method is based on the use of enthalpy concentration diagram, which contains the bubble point curve (saturated liquid curve), dew point curve (saturated vapour curve) and equilibrium tie lines. As compared to McCabe-Thiele’s method, this method_________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Rate of filtrate delivery is inversely proportional to the___________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Pick out the wrong statement about routing of fluids in a shell and tube heat exchanger ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  What is the minimum recommended ligament for square pitch arrangement in case of heat exchangers ?
Category: Chemical Engineering Mcqs,   Published by: teswesm