|
MCQs: Frictional force depends on ________
Category: Mechanical Engineering Questions, Published by: teswesm
|
|
MCQs: Which of the following conditions do not change the effect of couple?
Category: Mechanical Engineering Questions, Published by: teswesm
|
|
MCQs: If two concurrent forces A and B acting on a point are 200 N and 300 N. What is the magnitude of resultant force, if it makes an angle of 50° with each force?
Category: Mechanical Engineering Questions, Published by: teswesm
|
|
MCQs: What is the angle made by side of a square lamina, if it is freely suspended from a corner with the horizontal?
Category: Mechanical Engineering Questions, Published by: teswesm
|
|
MCQs: What is the C.G of an isosceles triangle of base 20 cm and side 40?
Category: Mechanical Engineering Questions, Published by: teswesm
|
|
MCQs: Uniformly distributed load of 5 kN acts on a simply supported beam of length 10 m. What are the reactions at end points of the beam?
Category: Mechanical Engineering Questions, Published by: teswesm
|
|
MCQs: What is the length of a train which crosses a bridge of 150 m in 20 sec with a speed of 40 km/h?
Category: Mechanical Engineering Questions, Published by: teswesm
|
|
MCQs: What are the limitations of string law?
Category: Mechanical Engineering Questions, Published by: teswesm
|
|
MCQs: Two cars X and Y move on adjacent roads in opposite directions. If velocity of car X and Y is 80 km/hr and 60 km/hr respectively, then what will be the relative velocity of car X w.r.t. Y?
Category: Mechanical Engineering Questions, Published by: teswesm
|
|
MCQs: In 5 seconds a body covers a distance of 50 m and in 10 seconds it covers 80 m with uniform acceleration. What is the distance traveled in 15 seconds?
Category: Mechanical Engineering Questions, Published by: teswesm
|
|
MCQs: What is the maximum distance traveled by a block moving upwards on an inclined plane of 30° with velocity of 20 m/s, if coefficient of friction is 0.23 between the block and inclined plane?
Category: Mechanical Engineering Questions, Published by: teswesm
|
|
MCQs: A constant force of 150 N is applied on a block of 5 kg on a horizontal surface. What is the time required to attain velocity of 40 m/sec by the block?
Category: Mechanical Engineering Questions, Published by: teswesm
|
|
MCQs: What is the angle of projection for a bullet fired over a horizontal plane, when horizontal range is equal to 4 times the maximum height?
Category: Mechanical Engineering Questions, Published by: teswesm
|
|
MCQs: What is the kinetic energy at the highest point, if at an angle of 30° with the horizontal a ball is projected with a kinetic energy E?
Category: Mechanical Engineering Questions, Published by: teswesm
|
|
MCQs: Which of the following factors are related by work energy principle?
Category: Mechanical Engineering Questions, Published by: teswesm
|
|
MCQs: What is the S.I unit of work done?
Category: Mechanical Engineering Questions, Published by: teswesm
|
|
MCQs: Which of the following force(s) is a type of conservative force?
Category: Mechanical Engineering Questions, Published by: teswesm
|
|
MCQs: What is the coefficient of restitution (e) for elastic impact?
Category: Mechanical Engineering Questions, Published by: teswesm
|
|
MCQs: If coefficient of restitution is zero during plastic impact, then ___________
Category: Mechanical Engineering Questions, Published by: teswesm
|
|
MCQs: Coefficient of restitution is the ratio of impulse during __________
Category: Mechanical Engineering Questions, Published by: teswesm
|
