Design of Masonry Structures Mcqs

Q.  Consider the following statements regarding provision of chases in masonry_________________?
(i) No chase should be permitted in a half brick load-bearing wall,
(ii) Vertical chases should not be closer than 2 m in any stretch of a wall,
(iii) Chases should be provided near to bearings of beams and lintels.
Select the the statements ?


a. (i) and (ii) are correct
b. (i) and (iii) are correct
c. (ii) and (iii) are correct
d. (i), (ii) and (iii) are correct


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  Drifters can be used to drill_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The correct sequence of drilling equipment for increasing size of holes in tunnels is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In compressed air tunneling, the volume of free air provided is______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following lining material is useful for shield driven tunnels in sub aqueous regions ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which one of the following tunnelling methods is used for laying under ground sewers ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The most suitable soil for compressed air tunneling is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following methods of tunneling is used for long tunnels at great depths ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  What is the correct sequence of the following events in rock tunnelling? 1. marking tunnel profile 2. loading explosives and blasting 3. checking misfire 4. mucking 5. removing foul gas 6. setting up and drilling 7. guniting Select the correct answer using the codes given below Codes ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which one of the following is considered to be an advantage of the heading and benching method of tunnel construction?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which one of the following is a component of a shield for tunnelling ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Drift method of tunnelling is used to construct tunnels in__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In Belgium method of tunneling _________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Ribs are used for strengthening and stiffening the liner plate for tunnels of diameter greater than_____________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If ‘D’ is the diameter of tunnel in meters, then the thickness of lining in mm, as per the empirical formula is given by_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following is not a component of the shield ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If ‘N’ is the number of shafts used, then the total number of feces available for attacking the excavation and construction in tunnels are_________________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Circular section of tunnels is not suitable for________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  As compared to a single free face, if a charge of explosive is placed equidistant from two faces, then the yield___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  What is the correct sequence of the following events of construction of a shaft in rock ? 1. drilling and blasting 2. timbering 3. pumping 4. mucking Select the correct answer using the codes given below Codes?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following are percussion drills ? (i) shot drill (ii) diamond drill (iii) wagon drill (iv) churn drill select correct answer?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts