Dock & Harbor Engineering Mcqs

Q.  By increasing the rise of lockgates_______________?
(i) the length of the lock gate will increase
(ii) transverse stress due to water pressure on the gate will increase
(iii) compressive force on the gate will increase
select the correct statements?


a. (i) and (ii) are correct
b. (i) and (iii) are correct
c. Only (ii) is correct
d. Only (iii) is correct


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  The capacity of parallel runway pattern depends upon______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  As per ICAO, for A, B, and C type of airports, maximum effective, transverse and longitudinal grades in percentage respectively are______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The length of runway under standard conditions is 2000 m. The elevation of airport site is 300 m. Its reference temperature is 33.05°C. If the runway is to be constructed with an effective gradient of 0.25 percent, the corrected runway length will be________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Zero fuel weight of an aircraft is_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  As per ICAO, for airports serving big aircrafts, the crosswind component should not exceed_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For determining the basic runway.length, the landing case requires that aircraft should come to a stop within p % of the landing distance. The value of p is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Runway threshold is indicated by a series of parallel lines starting from a distance of_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In Intrumental landing system, the middle markers are located___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The centre to centre spacing of heliport lighting along the periphery of landing and take off area should be______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Assertion A: The width of a taxiway is smaller than the runway width. Reason R : The speed of the aircraft on a taxiway is greater than that on runway.? Select your answer based on coding system given below
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  As per UK design criteria, if LCN of aircraft is between 1.25 to 1.5 times the LCN of pavement, then the number of movements allowed are__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The slope of the transitional surface for A, B and C type of runway shall be_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In approach areas of runways equipped with instrumental landing facilities any object within 4.5 km distance from runway end shall be considered as an obstruction if its height is more than______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The main disadvantage of angle nose out parking configuration of aircraft is that the_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following factors are taken into account for estimating the runway length required for aircraft landing ? 1. Normal maximum temperature 2. Airport elevation 3. Maximum landing weight 4. Effective runway gradient Select the correct answer using the codes given below Codes?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The runway length after correcting for elevation and temperature is 2845 m. If the effective gradient on runway is 0.5 percent then the revised runway length will be_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In an airport, if 4 groups of 5 gates each located well-separated are considered for traffic and the future to present traffic ratio is 3, then the total requirement of future gates will be______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Consider the following statements: Wind rose diagram is used for the purposes of_________________? 1. runway orientation 2. estimating the runway capacity 3. geometric design of holding apron select the correct answer?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Castor angle is defined as the angle______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Maximum gross take-off weight of an aircraft is__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts