|
MCQs: What is the minimum recommended ligament for square pitch arrangement in case of heat exchangers ?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: The normal range of velocity of water in pipes is _______________ m/sec?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: Brass valves are usually made for pipe sizes ______________ inches?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: The force due to wind load acting on a tall vessel depends upon its___________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: Pick out the wrong statement pertaining to the design of the distillation column?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: Hole diameter of the sieve trays in the distillation column ranges from ______________ mm?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: In case of 1.5″ heat exchanger tubes, the inside flow area _____________ with decrease in BWG?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: Hoop (circumferential) stress induced in a thin walled ‘Horton Sphere’ used for the storage of liquid ammonia under pressure is____________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: In the design of a paddle agitator, the ratio (paddle dia/tank dia) is normally taken as___________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: The centre to centre distance between two consecutive baffles in a shell and tube heat exchanger is called the baffle pitch or baffle spacing, which is more than 1/5th the I.D. of the shell. Which of the following is not a function of the baffles ?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: Any shell opening greater than 5 cms for a storage tank must be reinforced for reason of ____________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: In most of the shell and tube heat exchangers, the tube pitch is generally ______________ the tube diameter?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: Movement of pipeline caused by thermal expansion is taken care by providing ___________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: For a given fluid, as the pipe diameter increases, the pumping cost ____________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: In a vertical short tube evaporator (Calandria type), the ______________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: In a shell and tube heat exchanger for a given heat transfer surface area, smaller diameter tubes are favoured as compared to larger diameter ones; because the smaller diameter tubes ______________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: In a bag filter, the pressure drop increases directly as the___________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: When one of the fluids is highly corrosive and has fouling tendency, it should_____________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: To avoid the tearing off the plate of an edge, the margin (i.e., the minimum distance from the centre of the rivet hole to the nearest edge of the plate) should be equal to ____________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
|
MCQs: The distance between the centres of a rivet hole to the nearest edge of the plate is called _________________?
Category: Chemical Engineering Mcqs, Published by: teswesm
|
