Hydraulics & Fluid Mechanics Mcqs


Q.  At the centre line of a pipe flowing under pressure where the velocity gradient is zero, the shear stress will be_______________?

a. minimum
b. maximum
c. zero
d. negative value
e. could be any value


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  A solid cylinder of mass M and radius R rolls down an inclined plane without slipping. The acceleration of center of mass of rolling cylinder is________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  A cylinder will slip on an inclined plane of inclination 0 if the coefficient of static friction between plane and cylinder is_____________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If the angular distance, 0 = 2t3 – 3t2, the angular acceleration at t = 1 sec. is__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  A particle moves in a straight line and its position is defined by the equation x = 6 t2 – t3 where t is expressed in seconds and x in meters. The maximum velocity during the motion is_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Instantaneous center is at infinity when the angular velocity is _________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  A 2 m long ladder rests against a wall and makes an angle of 30° with the horizontal floor. Where will be the instantaneous center of rotation when the ladder starts slipping ? 1) 1.0 in from the wall 2) 1.732 m from the wall 3) 1.0 m above the floor 4) 1.732 m above the floor The correct answer is?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The angle of projection at which the horizontal range and maximum height of a projectile are equal to_____________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  A stone is thrown vertically upwards with a vertical velocity of 49 m/sec. It returns to the ground in________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If the direction of projection bisects the angle between the vertical and the inclined plane, then the range of projectile on the inclined plane is__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The angle of projection at which the horizontal range and maximum height of a projectile are equal to___________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  In a simple harmonic motion, the position of equilibrium is always_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The time period of a simple pendulum depends on__________________? 1) mass of suspended particle 2) length of the pendulum 3) acceleration due to gravity The correct answer is
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The maximum displacement of a particle executing S.H.M. corresponds to__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  A simple pendulum of length 1 has an energy E when its amplitude is A. If its amplitude is increased to 2 A, the energy becomes____________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The ratio of kinetic energy and potential energy of a simple harmonic oscillator, at a displacement equal to half its amplitude is given by__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Time period and length of a seconds pendulum respectively are_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  A particle is executing simple harmonic motion in a line 1.0 m long. If the time of one complete vibration is 1 sec, then the maximum velocity of the particle is___________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Joule is the unit of__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  A quantity whose dimensions are M2L2 T3 could be the product of_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If y is force and x is velocity, then dimensions of —=r are dx2__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm