Design of Steel Structures Mcqs

Q.  As per IS:800, in the plastic design, which of the following pairs are correctly matched? Working Loads Load factor________________?
(i) Dead load 1.7
(ii) Dead Load + imposed load 1.7
(iii) Dead load + load due to wind or 1.3 seismic forces
(iv) Dead load + imposed load + load 1.7
due to wind or seismic forces Of these statements


a. (i) and (ii) are correct
b. (i), (ii) and (iii) are correct
c. (ii) and (iii) are correct
d. only (i) is correct


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  compression force in two end posts The pin of a rocker bearing in a bridge is designed for_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The portal bracing in a truss bridge is used to_____________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The centrifugal force due to curvature of track is assumed to act on the bridge at a height of___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If the loaded length of span in meters of a railway steel bridge carrying a single track is 6 m, then impact factor is taken as_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The diameter of base of conical flare of a steel stack is_____________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The capacity of the smallest pressed steel tank is__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Steel tanks are mainly designed for_______________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Minimum pitch provided in riveted steel tanks is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  As per IS : 875, for the purposes of specifying basic wind velocity, the country has been divided into_____________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The external wind pressure acting on a roof depends on__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The basic wind speed is specified at a height ‘h’ above mean ground level in an open terrain. The value of’h’ is__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The live load for a sloping roof with slope 15°, where access is not provided to roof, is taken as_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For the buildings having a low permeability, the internal wind pressure acting normal to the wall and roof surfaces is taken as__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  To minimize the total cost of a roof truss, the ratio of the cost of truss to the cost of purlins shall be_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The minimum thickness of plates in a steel stack should be___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The maximum permissible span of asbestos cement sheets is______________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The maximum spacing of vertical stiffeners is_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Bearing stiffeners are provided at________________? i) the supports ii) the mid span iii) the point of application of concentrated loads The correct answer is?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The forces acting on the web splice of a plate girder are__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Minimum spacing of vertical stiffeners is limited to________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts