|
MCQs: For supersonic transport aircraft, the minimum turning radius of taxiway is________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Assertion A : Airport capacity during IFR conditions is usually less than that during VFR conditions. Reason R: During clear weather condition (VFR), the aircrafts on final approach to runway can be spaced closer during poor visibility conditions?
Select your answer based on the coding system given below?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The size of landing area for multiengined helicopters operating under 1FR conditions is______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The slope of the obstruction clearance line from the boundary of the heliport should be________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The width and interval of transverse centre line bars along the extended centre line of runway, in approach lighting system are_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: According to ICAO, all markings on the runways are___________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Calm period is the percentage of time during which wind intensity is less than______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The cruising speed of the aircraft is 500 kmph. If there is a head wind of 50 kmph, then the air speed and ground speed of the aircraft respectively will be_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: As per ICAO, the minimum basic runway length for A and E type of airport will be________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The length of clear zone for none instrument runway of a small aircraft is________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Consider the following statements regarding iCAO recommendation for correction to basic runway length_________________?
1. The basic runway length should be increased at the rate of 7 percent per 300 m rise in elevation above the mean sea level
2. The basic runway length after having been corrected for elevation should be further increased at the rate of 1 percent for every 1°C rise in airport reference temperature above the standard atmospheric temperature at that elevation
3. The runway length after having been corrected for elevation and temperature should be further increased at the rate of 20% for every 1 percent of effective gradient
Select the correct statment
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Assertion A : The ratio of arriving and departing aircrafts influences the airport capacity: Reason R :Landing operation is generally given priority over the taking off operation_________________?
Select your answer based on the coding system given below?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Malleability of a material can be defined as ______________________?
Category: Mechanical Engineering Questions, Published by: teswesm
|
|
MCQs: Mild steel belongs to the following category___________________?
Category: Mechanical Engineering Questions, Published by: teswesm
|
|
MCQs: Stress relaxation is- the phenomenon ___________________?
Category: Mechanical Engineering Questions, Published by: teswesm
|
|
MCQs: Isotropic materials are those which have the same ____________________?
Category: Mechanical Engineering Questions, Published by: teswesm
|
|
MCQs: The ability of a material to resist softening at high temperature is known as____________________?
Category: Mechanical Engineering Questions, Published by: teswesm
|
|
MCQs: The ultimate tensile strength and yield strength of most of the metals, when temperature falls from 0 to l00°C will _________________?
Category: Mechanical Engineering Questions, Published by: teswesm
|
|
MCQs: Points of arrest for iron correspond to__________________?
Category: Mechanical Engineering Questions, Published by: teswesm
|
|
MCQs: A material is known as allotropic or polymorphic if it __________________?
Category: Mechanical Engineering Questions, Published by: teswesm
|
