Environmental Engineering Mcqs

Q.  As compared to geometrical increase method of forecasting population, arithmetical increase method gives________________?

a. lesser value
b. higher value
c. same value
d. accurate value


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  A single rolling load of 8 kN rolls along a girder of 15 m span. The absolute maximum bending moment will be________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  When a uniformly distributed load, longer than the span of the girder, moves from left to right, then the maximum bending moment at mid section of span occurs when the uniformly distributed load occupies_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  When a series of wheel loads crosses a simply supported girder, the maximum bending moment under any given wheel load occurs when________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following is not the displacement method ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If in a rigid-jointed space frame, (6m + r) < 6j, then the frame is_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Effects of shear force and axial force on plastic moment capacity of a structure are respectively to_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following methods of structural analysis is a displacement method ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The fixed support in a real beam becomes in the conjugate beam a___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A simply supported beam deflects by 5 mm when it is subjected to a concentrated load of 10 kN at its centre. What will be deflection in a 1/10 model of the beam if the model is subjected to a 1 kN load at its centre ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  For a single point load W moving on a symmetrical three hinged parabolic arch of span L, the maximum sagging moment occurs at a distance x from ends. The value of x is__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Sinking of an intermediate support of a continuous beam________________? Consider the following statements 1. reduces the negative moment at support 2. increases the negative moment at support 3. reduces the positive moment at support 4. increases the positive moment at the centre of span
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  When a load crosses a through type Pratt truss in the direction left to right, the nature of force in any diagonal member in the left half of the span would_______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The deformation of a spring produced by a unit load is called _________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The width of the analogous column in the method of column analogy is _________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Muller Breslau’s principle for obtaining influence lines is applicable to___________________? i) trusses ii) statically determinate beams and frames iii) statically indeterminate structures, the material of which is elastic and follows Hooke’s law iv) any statically indeterminate structure The correct answer is ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Select the correct statement___.?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A load ‘W is moving from left to right support on a simply supported beam of span T. The maximum bending moment at 0.4 1 from the left support is___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In the displacement method of structural analysis, the basic unknowns are__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following methods of structural analysis is a force method ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  When a uniformly distributed load, shorter than the span of the girder, moves from left to right, then the conditions for maximum bending moment at a section is that___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts