|
MCQs: In the truss shown in given figure, the force in member BD is______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The moment of inertia of a circular section about any diameter D, is______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Pick up the correct statement from the following__________.?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Y are the bending moment, moment of inertia, radius of curvature, modulus of If M, I, R, E, F, and elasticity stress and the depth of the neutral axis at section, then________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The locus of the moment of inertia about inclined axes to the principal axis, is______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A steel plate d × b is sandwiched rigidly between two timber joists each D × B/2 in section. The steel will be (where Young’s modulus of steel is m times that of the timber)_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The general expression for the B.M. of a beam of length l is the beam carries M = (wl/2) x – (wx²/2)_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: In the truss, the force in the member AC is_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The point of contraflexure is the point where_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: d constant, the width of a cantilever of length l of uniform strength loaded with Keeping the depth a uniformly distributed load w varies from zero at the free end and________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: y/n) (1 – a l/r), is For calculating the allowable stress of long columns. The empirical formula 0 known as_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: For determining the support reactions at A and B of a three hinged arch, points B and Care joined and produced to intersect the load line at D and a line parallel to the load line through A at D’. Distances AD, DD’ and AD’ when measured were 4 cm, 3 cm and 5 cm respectively. The angle between the reactions at A and B is___________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The ratio of the maximum deflections of a simply supported beam with a central load W and of a cantilever of same length and with a load W at its free end, is________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A square column carries a load P at the centroid of one of the quarters of the square. If a is the side of the main square, the combined bending stress will be________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A material may fail if______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A shaft is subjected to bending moment M and a torque T simultaneously. The ratio of the maximum bending stress to maximum shear stress developed in the shaft, is____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A cantilever of length 2 cm and depth 10 cm tapers in plan from a width 24 cm to zero at its free end. If the modulus of elasticity of the material is 0.2 × 106 N/mm2, the deflection of the free end, is________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: At its elastic limit, the following statement is true, 0/E__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: In plastic analysis, the shape factor for a triangular section, is_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A steel bar 5 m × 50 mm is loaded with 250,000 N. If the modulus of elasticity of the material is 0.2 MN/mm2 and Poisson’s ratio is 0.25, the change in the volume of the bar is_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
