Process Equipment & Plant Design Mcqs for Chemical

Q.  An increase in the liquid resistance to interphase mass transfer and a resultant reduction in plate efficiency is caused by______________?

a. An increase in liquid viscosity
b. An increase in relative volatility for rectification columns
c. Decrease in gas solubility for absorbers
d. All A., B. and C.


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  An adequate clearance between the tray and the shell wall of a distillation column is provided to_____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A forced circulation long tube vertical evaporator as compared to the natural circulation evaporator__________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Cylindrical storage tanks used for the storage of volatile liquids (e.g., naphtha) have ______________ roofs?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  What is the slope of the operating line in the stripping section of a distillation column ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The safe height (h) to diameter D. ratio (i.e., h/d) for liquid/petro fuel storage tank of capacity more than 45 kilolitres is less than _________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Ponchon Savarit method is based on the use of enthalpy concentration diagram, which contains the bubble point curve (saturated liquid curve), dew point curve (saturated vapour curve) and equilibrium tie lines. As compared to McCabe-Thiele’s method, this method_________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Rate of filtrate delivery is inversely proportional to the___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Pick out the wrong statement about routing of fluids in a shell and tube heat exchanger ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  What is the minimum recommended ligament for square pitch arrangement in case of heat exchangers ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The normal range of velocity of water in pipes is _______________ m/sec?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Brass valves are usually made for pipe sizes ______________ inches?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The force due to wind load acting on a tall vessel depends upon its___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Pick out the wrong statement pertaining to the design of the distillation column?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Hole diameter of the sieve trays in the distillation column ranges from ______________ mm?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In case of 1.5″ heat exchanger tubes, the inside flow area _____________ with decrease in BWG?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Hoop (circumferential) stress induced in a thin walled ‘Horton Sphere’ used for the storage of liquid ammonia under pressure is____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In the design of a paddle agitator, the ratio (paddle dia/tank dia) is normally taken as___________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The centre to centre distance between two consecutive baffles in a shell and tube heat exchanger is called the baffle pitch or baffle spacing, which is more than 1/5th the I.D. of the shell. Which of the following is not a function of the baffles ?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Any shell opening greater than 5 cms for a storage tank must be reinforced for reason of ____________________?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In most of the shell and tube heat exchangers, the tube pitch is generally ______________ the tube diameter?
Category: Chemical Engineering Mcqs,   Published by: T-Code Scripts