Process Control & Instrumentation Mcqs for Chemical


Q.  A typical example of a physical system with under damped characteristic is a____________________?

a. U-tube manometer
b. Spring loaded diaphragm valve
c. CSTR with first order reaction
d. Thermocouple kept immersed in a liquid filled thermowell


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  Pick out the one which is a first order instrument ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  What is the value of ‘q’ for saturated vapor feed to a distillation column? (where q = fraction of the feed stream that is liquid ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Large process vessels operating under extreme temperature and pressure conditions are normally clad/ lined with materials like stainless steel, aluminium, nickel & its alloys, copper & its alloys and titanium. The cladding thickness is generally about ______________ percent of the total thickness?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Pick out the wrong statement pertaining to the design of a horizontal tube evaporator ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  In a distillation column, bubble caps are located on trays with a pitch of ______________ times the outside diameter of the caps?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  ______________ closure is the weakest enclosure for cylindrical vessels?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  High pressure fluid in a shell and tube heat exchanger should preferably be routed through the________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  What is the slope of the feed line, if the feed to a distillation column is a saturated liquid ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  ___________ tower is the most suitable gas-liquid contacting device involving highly corrosive fluids?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  For a cylindrical shell, (subject to the thickness of uppermost course being more than the minimum for dia of the tank in question), the thickness of the courses of shell_________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Pick out the wrong statement?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  The minimum baffle height should be ______________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  In actual operation of distillation column, the vapour is not distributed uniformly among the bubble caps, primarily because of the_______________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Pick out the wrong statement pertaining to shell and tube heat exchanger_______________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  In case of plain carbon steel, butt welded joints are used for shell plate thickness ≤ _____________ cms?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Practical dividing line between a ductile and brittle materials is suggested, when the ultimate elongation is about 5%. Generally, larger the knuckle radius, stronger is the corner torus section of a head. The knuckle radius provided should be less than ______________ of the head?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  The LMTD correction factor (FT) is defined as the __________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Which of the following is the best tube material from thermal conductivity point of view alone ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Power required for agitation depends upon the______________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Stage efficiency for packed tower varies with the____________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm