|
MCQs: The general expression for the B.M. of a beam of length l is the beam carries M = (wl/2) x – (wx²/2)_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: In the truss, the force in the member AC is_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The point of contraflexure is the point where_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: d constant, the width of a cantilever of length l of uniform strength loaded with Keeping the depth a uniformly distributed load w varies from zero at the free end and________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: y/n) (1 – a l/r), is For calculating the allowable stress of long columns. The empirical formula 0 known as_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: For determining the support reactions at A and B of a three hinged arch, points B and Care joined and produced to intersect the load line at D and a line parallel to the load line through A at D’. Distances AD, DD’ and AD’ when measured were 4 cm, 3 cm and 5 cm respectively. The angle between the reactions at A and B is___________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The ratio of the maximum deflections of a simply supported beam with a central load W and of a cantilever of same length and with a load W at its free end, is________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A square column carries a load P at the centroid of one of the quarters of the square. If a is the side of the main square, the combined bending stress will be________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A material may fail if______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A shaft is subjected to bending moment M and a torque T simultaneously. The ratio of the maximum bending stress to maximum shear stress developed in the shaft, is____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A cantilever of length 2 cm and depth 10 cm tapers in plan from a width 24 cm to zero at its free end. If the modulus of elasticity of the material is 0.2 × 106 N/mm2, the deflection of the free end, is________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: At its elastic limit, the following statement is true, 0/E__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: In plastic analysis, the shape factor for a triangular section, is_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A steel bar 5 m × 50 mm is loaded with 250,000 N. If the modulus of elasticity of the material is 0.2 MN/mm2 and Poisson’s ratio is 0.25, the change in the volume of the bar is_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: A steel rod 1 metre long having square cross section is pulled under a tensile load of 8 tonnes. The extension in the rod was 1 mm only. If Esteel = 2 × 106 kg/cm2, the side of the rod, is_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Total strain energy theory for the failure of a material at elastic limit, is known_________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The horizontal deflection of a parabolic curved beam of span 10 m and rise 3 m when loaded with a uniformly distributed load l t per horizontal length is (where Ic is the M.I. at the crown, which varies as the slope of the arch)___________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Stress may be expressed in Newtons___________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: The vertical reaction for the arch is________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
|
MCQs: Flat spiral springs_______________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
