# RCC Structures Design Mcqs

Q.  A pre-stressed concrete member__________________?

a. Is made of concrete
b. Is made of reinforced concrete
c. Is stressed after casting
d. Possesses internal stresses

ANSWER: See Answer

No explanation is available for this question!
 MCQs:  If the effective length of a 32 cm diameter R.C.C. column is 4.40 m, its slenderness ratio, is_______________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  The anchorage value of a hook is assumed sixteen times the diameter of the bar if the angle of the bend, is___________________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  The number of treads in a flight is equal to_______________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  The shear reinforcement in R.C.C. is provided to resist__________________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  A simply supported beam 6 m long and of effective depth 50 cm, carries a uniformly distributed load 2400 kg/m including its self weight. If the lever arm factor is 0.85 and permissible tensile stress of steel is 1400 kg/cm2, the area of steel required, is___________________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  The amount of reinforcement for main bars in a slab, is based upon___________________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  The minimum cube strength of concrete used for a pre-stressed member, is________________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  If Sb, is the average bond stress on a bar of diameter subjected to maximum stress , the length of the embedment is given by_____________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  effective depth and depth of the neutral axis respectively of a singly reinforced If d and n are the beam, the lever arm of the beam, is_________________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  bending moment of a simply supported slab is M Kg.cm, the effective depth of the If the maximum slab is (where Q is M.R. factor)________________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  If the sides of a slab simply supported on edges and spanning in two directions are equal, the maximum bending moment is multiplied by_________________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  The width of the flange of a T-beam, which may be considered to act effectively with the rib depends upon____________________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  Pick up the incorrect statement from the following. The intensity of horizontal shear stress at the elemental part of a beam section, is directly proportional to__________________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  Pick up the true statement from the following? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  Pick up the correct statement from the following_? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  Dimensions of a beam need be changed if the shear stress is more than_______________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  The effective width of a column strip of a flat slab, is_______________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  The length of lap in tension reinforcement should not be less than the bar diameter × (actual tension / four times the permissible average bond stress) if it is more than_______________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  As the percentage of steel increases________________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts MCQs:  For a number of columns constructed in a rcjw, the type of foundation provided, is_______________? Category: Civil Engineering Mcqs,   Published by: T-Code Scripts