RCC Structures Design Mcqs


Q.  A pre-stressed concrete member is preferred because___________________?

a. Its dimensions are not decided from the diagonal tensile stress
b. Large size of long beams carrying large shear force need not be adopted
c. Removal of cracks in the members due to shrinkage
d. All the above


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  If is the uniformly distributed load on a circular slab of radius maximum positive radial moment at its centre, is__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If the ratio of the span to the overall depth does not exceed 10, the stiffness of the beam will ordinarily be satisfactory in case of a__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  For M 150 grade concrete (1:2:4) the moment of resistance factor is_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The spacing of transverse reinforcement of column is decided by the following consideration_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The self-weight of the footing, is_____________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If the bearing capacity of soil is 10 tonnes/cm2 and the projection of plain concrete footing from walls, is a cm, the depth D of footing is_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  After pre-stressing process is completed, a loss of stress is due to______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If R and T are rise and tread of a stair spanning horizontally, the steps are supported by a wall on one side and by a stringer beam on the other side, the steps are designed as beams of width_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If p1 and P2 are effective lateral loadings at the bottom and top exerted by a level earth subjected to a super-load on the vertical face of height h of a retaining wall, the horizontal pressure p per unit length of the wall, is____________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The transverse reinforcements provided at right angles to the main reinforcement_______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Long and short spans of a two way slab are l and l and load on the slab acting on strips parallel to lx and ly be wx and wy respectively. Accordingy to xRankine Grashoff theory___________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  In the zone of R.C.C. beam where shear stress is less than 5 kg/cm2, nominal reinforcement is provided at a pitch of________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  High strength concrete is used in pre-stressed member________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  on a circular slab of radius , the maximum radial moment at the centre of the If is the load slab, is WR²/16_____________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If the permissible compressive and tensile stresses in a singly reinforced beam are 50 kg/cm2 and 1400 kg/cm2 respectively and the modular ratio is 18, the percentage area At of the steel required for an economic section, is__________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The modular ratio m of a concrete whose permissible compressive stress is C, may be obtained from the equation.
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Enlarged head of a supporting column of a flat slab is technically known as______________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  If A is the area of the foundation of a retaining wall carrying a load W and retaining earth of weight w per unit volume, the minimum depth (h) of the foundation from the free surface of the earth, is )/(1 + sin )]_________________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  Thickened part of a flat slab over its supporting column, is technically known as_____________?
Category: Civil Engineering Mcqs,   Published by: teswesm
MCQs:  The pitch of the main bars in a simply supported slab, should not exceed its effective depth by_____________?
Category: Civil Engineering Mcqs,   Published by: teswesm