Process Equipment & Plant Design Mcqs for Chemical


Q.  A head comprises of straight flange section, corner torus, section and central dished section. Crown radius and knuckle radius in a head is related respectively to the__________________?

a. Central dished section and corner torus section
b. Corner torus section and central dished section
c. Central dished section and straight flange section
d. Straight flange section and corner torus section


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  Fouling factor must be included in the calculation of overall design heat transfer coefficient, when the liquid__________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Which of the following is not a graphical method (but is an analytical method) for the calculation of theoretical number of stages in case of continuous binary distillation ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  For storing hazardous chemicals in large storage tanks, the minimum safe distance between the two tanks should range between ______________________ times the tank diameter?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  If a single tube pass heat exchanger is converted to two passes; for the same flow rate, the pressure drop per unit length in tube side will _____________ times?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Rivets are generally specified by the____________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Shortest distance between two tubes is___________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Bubble cap plate column is___________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Multiple blade paddle agitator is used for mixing high viscosity liquids/paste in which the paddle diameter is commonly 0.8 times the tank diameter. However, the width of the blade is in the range of ______________ times the paddle diameter?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  With increase in temperature drop (in a shell and tube heat exchanger), the LMTD correction factor, FT_________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  The distance between the top of the slots and the liquid surface when the static liquid is just ready to flow over the overflow weir is called____________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Minimum recommended baffle spacing in a shell and tube heat exchanger is about (where, D = shell diameter) ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  In a cylindrical vessel subjected to internal pressure, the longitudinal stress ζL and the circumferential stress, ζn are related by___________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Larger depth of liquid on the trays of a distillation column_________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Needle valves are generally not used for___________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  In common bubble cap distillation column design practice, riser area is approximately equal to (where, Aa = Annular passage area, and Sa = Slot area) ?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Welded joint efficiency in the design of chemical process equipment is taken as_________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Floating head heat exchangers are used for the____________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Theoretically calculated diameter of the stripping section of the continuous rectification column is ______________ that of the enriching section?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  Safety valves are provided in chemical equipments to guard against excessive_________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm
MCQs:  An adequate clearance between the tray and the shell wall of a distillation column is provided to_____________________?
Category: Chemical Engineering Mcqs,   Published by: teswesm