Applied Mechanics & Graphic Statics Mcqs

Q.  A force P of 50 N and another force Q of unknown magnitude act at 90° to each other. They are balanced by a force of 130 N. The magnitude of Q is__________________?

a. 60 N
b. 80 N
c. 100 N
d. 120 N


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  The angle of projection at which the horizontal range and maximum height of a projectile are equal to___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In a simple harmonic motion, the position of equilibrium is always_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The time period of a simple pendulum depends on__________________? 1) mass of suspended particle 2) length of the pendulum 3) acceleration due to gravity The correct answer is
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The maximum displacement of a particle executing S.H.M. corresponds to__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A simple pendulum of length 1 has an energy E when its amplitude is A. If its amplitude is increased to 2 A, the energy becomes____________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The ratio of kinetic energy and potential energy of a simple harmonic oscillator, at a displacement equal to half its amplitude is given by__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Time period and length of a seconds pendulum respectively are_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A particle is executing simple harmonic motion in a line 1.0 m long. If the time of one complete vibration is 1 sec, then the maximum velocity of the particle is___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Joule is the unit of__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A quantity whose dimensions are M2L2 T3 could be the product of_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If y is force and x is velocity, then dimensions of —=r are dx2__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The dimensions of centrifugal force are__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The unit of rotational inertia of a body in C.G.S system is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In SI units, the units of force and energy are respectively___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A cable loaded with 10 kN/m of span is stretched between supports in the same horizontal line 100 m apart. If the central dip is 10 m, then the maximum and minimum pull in the cable respectively are____________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Impulse can be obtained from a_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following is a scalar quantity ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Coefficient of friction depends on__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If a body is lying on a plane whose inclination with the horizontal is less than the angle of friction, then___________________? 1) a force is required to move the body upwards 2) a force is required to move the body downward 3) the body will not be in equilibrium The correct answer is?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A ladder of weight ‘w’ rests against a smooth vertical wall, and rests on rough horizontal ground, the coefficient of friction between the ladder and the ground being 1/4. The maximum angle of inclination of the ladder to the vertical, if a man of weight ‘w’ is to walk to the top of it safely, is tan’1 x, where x is___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts