Strength of Materials Test Questions


Q.  A circular pipe is subjected to maximum shear force of 60 kN. What is the diameter of the pipe if maximum allowable shear stress is 5 Mpa?

a. 27.311 mm
b. 75.56 mm
c. 142.72 mm
d. 692.10 mm


ANSWER: See Answer
 
No explanation is available for this question!
MCQs:  For designing ductile materials, which of the following theories is/are used?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  Shear stress energy theory is called as ______
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  Which gear is used if the axes of two shafts are neither intersecting nor parallel?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  Spiral gears are used only if the axes of two shafts are non-intersecting, non-parallel and __________.
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  In which of the following processes, tooth ends are made thinner?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  What are the advantages of smaller pressure angles?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  In force analysis of spur gears which component of force assists the rotation on driven gear?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  A helical gear has normal module of 6 mm. What is the transverse module if helix angle is 25°?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  What is the axial pitch for helical gears if helix angle is 25° and normal module is 7?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  Which of the following formulae of velocity factor (K) is considered if helical gears of medium accuracy are manufactured by hobbing process followed by shaving?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  What is the pitch cone distance of bevel gear, if pitch circle diameter of bevel pinion and gear is 20 and 30 respectively?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  A pair of straight bevel gears consists of 16 pinion teeth and 42 gear teeth. What are the pitch cone angles of pinion and gear? 67.60° & 32.4°?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  What is the frictional torque acting on a cylindrical roller bearing of 50 mm diameter which is subjected to radial load of 30 kN and has coefficient of friction 0.0011?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  A cylindrical roller bearing is subjected to frictional torque of 500 N-mm. What is the approximate power loss if the shaft rotates at 1500 r.p.m?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  The expected rating life of roller bearings rotating at 1000 r.p.m. is 30000 hours and equivalent dynamic load of 4000 N acts on it. What is the basic dynamic capacity of the bearing?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  What is the effect of large diametral quotient on worm and worm wheel?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  A standard worm gear pair is designated as 4/40/10/8, what does number 10 in it indicate?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  A worm gear pair is designated as 1/30/10/8. What is the face width of the worm gear?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  Which of the following belts is used when axes of two shafts are perpendicular and intersecting?
Category: Mechanical Engineering Questions,   Published by: teswesm
MCQs:  Friction ply used in multiple-ply belts is made of ___________
Category: Mechanical Engineering Questions,   Published by: teswesm