MCQs: An ordinate in a funicular polygon represents__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: In which of the following trusses, the method of substitution is required for determining the forces in all the members of the truss by graphic statics ?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: The number of funicular polygons which can be drawn to pass through two specified points in the space diagram are__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: If the given forces P,, P2, P3 and P4 are such that the force polygon does not close, then the system will___________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: Williot-Mohr diagram is used to determine deflection in__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: For a non-concurrent force system to be in equilibrium__________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: The condition of equilibrium for any system of forces in a plane is____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: A funicular polygon cannot be made to pass through___________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: The pole distance is measured in___________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: The member forces in a statically in determinate truss____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: The graphical method of determining the forces in the members of a truss is based on________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: The force polygon representing a set of forces in equilibrium is a_____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: A system of copianar forces is in equilibrium when___________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: Free body diagram is an____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: In a lifting machine a weight of 5 kN is lifted through 200 mm by an effort of 0.1 kN moving through 15 m. The mechanical advantage and velocity ratio of the machine are respectively_____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: A stone was thrown vertically upwards from the ground with a velocity of 50 m/sec. After 5 seconds another stone was thrown vertically upwards from the same place. If both the stones strike the ground at the same time, then the velocity with which the second stone was thrown should be (Assume g = 10 m/sec2)______________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: A particle is dropped from a height of 3 m on a horizontal floor, which has a coefficient of restitution with the ball of 1/2. The height to which the ball will rebound after striking the floor is____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: One Joule is equivalent to________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: If a flywheel increases its speed from 10 rpm to 20 rpm in 10 seconds, then its angular acceleration is_____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|
MCQs: A car goes round a curve of radius 100 m at 25 m/sec. The angle to the horizontal at which the road must be banked to prevent sideways friction on the car wheels is tan”1 x, where x is (Assume g = 10 m/sec2)_____________________?
Category: Civil Engineering Mcqs, Published by: teswesm
|