Design of Masonry Structures Mcqs

Q.  A 200 mm thick wall made of modular bricks is 5 m long between cross walls and 3.8 m clear height between RCC slabs at top and bottom. The slenderness ratio of the wall is________________?

a. 15
b. 19
c. 20
d. 25


ANSWER: See Answer
 
No explanation is available for this question!
TasDia Network - Mcqs | Signature | Lyrics
MCQs:  If the ratio of center to center spacing of intersecting walls to actual thickness of intersecting wall is more than 20, then the stiffening coefficient for wall proper will be_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Assertion A : For eccentricity ratio exceeding 1/6, effective thickness of masonry will get reduced. Reason R : For eccentricity ratio exceeding 1/6, there will be tension on one side of the member? Select your answer according to the codes give below.
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Maximum slenderness ratio of load bearing walls for a dwelling having more than 2 storeys________________? i) shall not exceed 12 if lime mortar is used ii) shall not exceed 18 if cement lime mortar 1:2:9 is used iii) shall not exceed 24 if cement mortar 1:6 is used the correct statments is ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Consider the following statements? 1. Masonry in rich cement mortar though having good strength with high shrinkage is much liable for surface cracks. 2. Lime mortar possesses poor workability and poor water retentivity and also suffers high shrinkage. 3. Masonry in lime mortar has better resistance against rain penetration and is less liable to crack when compared to masonry in cement mortar. Which of these statements are correct?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  A good blast with a good yield is obtained if the cut hole is___________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Drifters can be used to drill_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The correct sequence of drilling equipment for increasing size of holes in tunnels is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In compressed air tunneling, the volume of free air provided is______________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following lining material is useful for shield driven tunnels in sub aqueous regions ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which one of the following tunnelling methods is used for laying under ground sewers ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  The most suitable soil for compressed air tunneling is________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following methods of tunneling is used for long tunnels at great depths ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  What is the correct sequence of the following events in rock tunnelling? 1. marking tunnel profile 2. loading explosives and blasting 3. checking misfire 4. mucking 5. removing foul gas 6. setting up and drilling 7. guniting Select the correct answer using the codes given below Codes ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which one of the following is considered to be an advantage of the heading and benching method of tunnel construction?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which one of the following is a component of a shield for tunnelling ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Drift method of tunnelling is used to construct tunnels in__________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  In Belgium method of tunneling _________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Ribs are used for strengthening and stiffening the liner plate for tunnels of diameter greater than_____________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  If ā€˜Dā€™ is the diameter of tunnel in meters, then the thickness of lining in mm, as per the empirical formula is given by_________________?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts
MCQs:  Which of the following is not a component of the shield ?
Category: Civil Engineering Mcqs,   Published by: T-Code Scripts